Difference between revisions of "USB8x8 Setup"
From eMDeeWiki
Jump to navigationJump to search (Created page with '== USB8x8 Windows Setup == * Download the following zip file and unzip it to a folder on the computer where the updates will be performed: * Plug the USB audio device into a USB…') |
|||
| Line 1: | Line 1: | ||
| − | == USB8x8 Windows Setup == | + | == USB8x8 Windows 10 Setup and Verification == |
| − | + | Follow these instructions to setup and verify the operation of the USB8x8 audio interface. Before you begin, make sure that no other applications that use the sound device are running (stop CGCS and CGSS, etc.). It is also a good idea to perform these steps from a fresh power-on state so that any previous settings from applications won't affect the results. | |
| − | |||
| − | |||
| − | + | * Open the Sound Control Panel by right-clicking the Windows Start button and selecting ''Control Panel''. | |
| + | * Select ''Hardware and Sound'' from the Control Panel, then select ''Sound'' from the next window. | ||
| + | * From the Sound Control Panel select the ''Playback'' tab - you should see devices similar to this: | ||
| − | * Click the | + | |
| + | [[File:Usb8x8_Playback.PNG]] | ||
| + | |||
| + | |||
| + | * Right-click on ''USB 8x8 [0] Chan 3-4'' and select ''Properties'' | ||
| + | * Click the ''Levels'' tab and set the volume level as shown below: | ||
| + | |||
| + | |||
| + | [[File:Usb8x8_Playback_Levels.PNG]] | ||
| + | |||
| + | |||
| + | * Close the ''Line Out Properties'' window by clicking ''OK''. | ||
| + | * From the Sound Control Panel select the ''Recording'' tab - you should see sound devices similar to this: | ||
| + | |||
| + | |||
| + | [[File:Usb8x8_Capture_Devices.PNG]] | ||
| + | |||
| + | |||
| + | * Right-click on ''USB 8x8 [0] Chan 3-4'' and select ''Properties'' | ||
| + | * Click the ''Levels'' tab and set the volume levels as shown below: | ||
| + | |||
| + | |||
| + | [[File:Usb8x8_Capture_Levels.PNG]] | ||
| + | |||
| + | |||
| + | * Click the ''Listen'' tab. | ||
| + | * Click the checkbox for ''Listen to this device''. | ||
| + | * Use the drop-list below ''Playback through this device:'' to select ''Line Out (USB 8x8[0] Chan 3-4)''. | ||
| + | * Click ''Apply''. | ||
| + | |||
| + | |||
| + | [[File:Usb8x8_Listen.PNG]] | ||
| + | |||
| + | |||
| + | * You should now be able to hear inputs 3 & 4 being routed to outputs 3 & 4 (e.g. speak into the Commander microphone and you should hear your voice in the Commander headset). | ||
Revision as of 17:08, 5 December 2016
USB8x8 Windows 10 Setup and Verification
Follow these instructions to setup and verify the operation of the USB8x8 audio interface. Before you begin, make sure that no other applications that use the sound device are running (stop CGCS and CGSS, etc.). It is also a good idea to perform these steps from a fresh power-on state so that any previous settings from applications won't affect the results.
- Open the Sound Control Panel by right-clicking the Windows Start button and selecting Control Panel.
- Select Hardware and Sound from the Control Panel, then select Sound from the next window.
- From the Sound Control Panel select the Playback tab - you should see devices similar to this:
- Right-click on USB 8x8 [0] Chan 3-4 and select Properties
- Click the Levels tab and set the volume level as shown below:
- Close the Line Out Properties window by clicking OK.
- From the Sound Control Panel select the Recording tab - you should see sound devices similar to this:
- Right-click on USB 8x8 [0] Chan 3-4 and select Properties
- Click the Levels tab and set the volume levels as shown below:
- Click the Listen tab.
- Click the checkbox for Listen to this device.
- Use the drop-list below Playback through this device: to select Line Out (USB 8x8[0] Chan 3-4).
- Click Apply.
- You should now be able to hear inputs 3 & 4 being routed to outputs 3 & 4 (e.g. speak into the Commander microphone and you should hear your voice in the Commander headset).
